Have I bricked my pvr (remote control)?
 

Keith wrote:

I seem to be stuffed; resetting the DVD (press+hold channel up/down button
for 10 seconds) does activate Setup but doesn't reset the remote, so can't
select/change any setup items. Is there a "secret" pinhole somewhere to
force a reset (as in Psion 3A, TomTom etc)?

I haven't been following this but have you tried taking the batteries
out and leaving it for a while?

Bill

Have I bricked my pvr (remote control)? UPDATE!!!
 

"Keith" wrote in message
...

"Richard Tobin" wrote in message
...
In article ,
Keith wrote:

I seem to be stuffed

I'd start looking for a remote to borrow... perhaps from the shop
where you bought it?

Oh, and try removing the batteries from the remote for a while, then
trying again.

-- Richard

Already tried these...
Just returned from Panasonic shop - very helpful but only solution is to
return the recorder to store of purchase, John Lewis, 40 miles away!

Hopefully there's an "Engineers" remote of some jump switches to (re)set
in the recorder.

Keith

Decided to have a coffee before setting out, gave the recorder its last
chance before being returned - remote worked! Panic over.
Don't know what happened, except that I took the recorder remote with me, so
it wasn't near the tv for an hour or so (warnings in manual about "nearby
devices"). Probably not relevant but SWMBO is now a happy bunny.

Thanks for the help,

Keith

Have I bricked my pvr (remote control)?
 

Keith wrote:
I have a Panasonic DMR-XS350EB - worked fine.
Today the TV (ancient Protech) failed so I bought a Panasonic TX-L32X20B,
theory being Panasonic DVD Recorder/Panasonic TV combo, no problems.
Reality: whilst setting up DVD remote to control TV (it worked fine when I
tuned it for the Protech) I have got the DVD displaying "DVD 3" and the
remote no longer controls the DVD recorder, but does, now, work the TV
on/off, vol, CH and AV buttons.
I've tried the "hard" DVD reset (pressing up-and-down channel buttons, on
DVD recorder, for 5 seconds) - display still shows "DVD 3" and DVD remote
still does not control the DVD recorder - which has started to record a
couple of programmes setup earlier this week.
Which key sequences do I require to get my DVD recorder remote to work
again?

TIA

Keith


Press the power button and 3 on the remote control together for a few
seconds then it should work. If you want to revert to DVD 1 then you can
now get in the 350's set-up and change it back. HTH

--
Adrian

Have I bricked my pvr (remote control)?
 

Keith wrote:
"Richard Tobin" wrote in message
...
In article ,
Keith wrote:

I seem to be stuffed
I'd start looking for a remote to borrow... perhaps from the shop
where you bought it?

Oh, and try removing the batteries from the remote for a while, then
trying again.

-- Richard

Already tried these...
Just returned from Panasonic shop - very helpful but only solution is to
return the recorder to store of purchase, John Lewis, 40 miles away!

Hopefully there's an "Engineers" remote of some jump switches to (re)set in
the recorder.

Keith



It is definitely the remote, as Richard said, press 3 and OK together on
the remote for more than 5 seconds and it should then operate the
recorder, after that you can set the TV code for that it is TV power 01
for a Panasonic TV.

--
Adrian

Have I bricked my pvr (remote control)?
 

"Adrian" wrote in message
om...
Keith wrote:
I have a Panasonic DMR-XS350EB - worked fine.
Today the TV (ancient Protech) failed so I bought a Panasonic TX-L32X20B,
theory being Panasonic DVD Recorder/Panasonic TV combo, no problems.
Reality: whilst setting up DVD remote to control TV (it worked fine when
I tuned it for the Protech) I have got the DVD displaying "DVD 3" and the
remote no longer controls the DVD recorder, but does, now, work the TV
on/off, vol, CH and AV buttons.
I've tried the "hard" DVD reset (pressing up-and-down channel buttons, on
DVD recorder, for 5 seconds) - display still shows "DVD 3" and DVD remote
still does not control the DVD recorder - which has started to record a
couple of programmes setup earlier this week.
Which key sequences do I require to get my DVD recorder remote to work
again?

TIA

Keith
Press the power button and 3 on the remote control together for a few
seconds then it should work. If you want to revert to DVD 1 then you can
now get in the 350's set-up and change it back. HTH

--
Adrian

Has the OP used the HDMI cables from his DVD recorder to the TV... I did and
alsorts of funny things started to happen with my TV and DVD Recorder, both
made by Panasonic

If using HDMI cale, suggest you unplug it

Jim

Have I bricked my pvr (remote control)?
 

"Adrian" wrote in message
om...
Keith wrote:
"Richard Tobin" wrote in message
...
In article ,
Keith wrote:

I seem to be stuffed
I'd start looking for a remote to borrow... perhaps from the shop
where you bought it?

Oh, and try removing the batteries from the remote for a while, then
trying again.

-- Richard

Already tried these...
Just returned from Panasonic shop - very helpful but only solution is to
return the recorder to store of purchase, John Lewis, 40 miles away!

Hopefully there's an "Engineers" remote of some jump switches to (re)set
in the recorder.

Keith



It is definitely the remote, as Richard said, press 3 and OK together on
the remote for more than 5 seconds and it should then operate the
recorder, after that you can set the TV code for that it is TV power 01
for a Panasonic TV.

--
Adrian

I'd already tried that option (see earlier in this thread) along with other
numerics suggested, without success.
However, I gave the kit a 'last-chance' between returning from the Panasonic
shop and going to JLs - I'd taken (just) the remote with me - and it now
worked!

Have I bricked my pvr (remote control)?
 

the_constructor wrote:
"Adrian" wrote in message
om...
Keith wrote:
I have a Panasonic DMR-XS350EB - worked fine.
Today the TV (ancient Protech) failed so I bought a Panasonic TX-L32X20B,
theory being Panasonic DVD Recorder/Panasonic TV combo, no problems.
Reality: whilst setting up DVD remote to control TV (it worked fine when
I tuned it for the Protech) I have got the DVD displaying "DVD 3" and the
remote no longer controls the DVD recorder, but does, now, work the TV
on/off, vol, CH and AV buttons.
I've tried the "hard" DVD reset (pressing up-and-down channel buttons, on
DVD recorder, for 5 seconds) - display still shows "DVD 3" and DVD remote
still does not control the DVD recorder - which has started to record a
couple of programmes setup earlier this week.
Which key sequences do I require to get my DVD recorder remote to work
again?

TIA

Keith
Press the power button and 3 on the remote control together for a few
seconds then it should work. If you want to revert to DVD 1 then you can
now get in the 350's set-up and change it back. HTH

--
Adrian

Has the OP used the HDMI cables from his DVD recorder to the TV... I did and
alsorts of funny things started to happen with my TV and DVD Recorder, both
made by Panasonic

If using HDMI cale, suggest you unplug it

Jim


An HDMI cable is by far the best way to connect a Panasonic DMR-XS350 to
the TV as it records in HD to the hard disc. I use HDMI with no problems
at all.

--
Adrian

Have I bricked my pvr (remote control)?
 

"Adrian" wrote in message
...
the_constructor wrote:
"Adrian" wrote in message
om...
Keith wrote:
I have a Panasonic DMR-XS350EB - worked fine.
Today the TV (ancient Protech) failed so I bought a Panasonic
TX-L32X20B, theory being Panasonic DVD Recorder/Panasonic TV combo, no
problems.
Reality: whilst setting up DVD remote to control TV (it worked fine
when I tuned it for the Protech) I have got the DVD displaying "DVD 3"
and the remote no longer controls the DVD recorder, but does, now, work
the TV on/off, vol, CH and AV buttons.
I've tried the "hard" DVD reset (pressing up-and-down channel buttons,
on DVD recorder, for 5 seconds) - display still shows "DVD 3" and DVD
remote still does not control the DVD recorder - which has started to
record a couple of programmes setup earlier this week.
Which key sequences do I require to get my DVD recorder remote to work
again?

TIA

Keith
Press the power button and 3 on the remote control together for a few
seconds then it should work. If you want to revert to DVD 1 then you can
now get in the 350's set-up and change it back. HTH

--
Adrian

Has the OP used the HDMI cables from his DVD recorder to the TV... I did
and alsorts of funny things started to happen with my TV and DVD
Recorder, both made by Panasonic

If using HDMI cale, suggest you unplug it

Jim
An HDMI cable is by far the best way to connect a Panasonic DMR-XS350 to
the TV as it records in HD to the hard disc. I use HDMI with no problems
at all.

--
Adrian

I had my Panasonic TV connected to my Panasonic DVD recorder and could nopt
work out why, everytime I switched the TV off to stanby with it's remote, it
switched the DVD Recorder off permanently.

Visited the shop where I got both items from and the salesman was mystified.
They sent the TV installer to see if he could work out what I was meaning.
He was baffled also when he tried it.

When I told him that the only thing I had done was put the HDMI cable on he
said that was the problem. Removed it and all is well again now.

Jim

Have I bricked my pvr (remote control)?
 

In article ,
the_constructor wrote:
I had my Panasonic TV connected to my Panasonic DVD recorder and could nopt
work out why, everytime I switched the TV off to stanby with it's remote, it
switched the DVD Recorder off permanently.

On my Panasonic TV, this is controlled by "Standby Power Save" in
"Link Settings" in the "System" menu.

-- Richard

Have I bricked my pvr (remote control)?
 

Has the OP used the HDMI cables from his DVD recorder to the TV... I did
and alsorts of funny things started to happen with my TV and DVD
Recorder, both made by Panasonic

If using HDMI cale, suggest you unplug it

Jim
An HDMI cable is by far the best way to connect a Panasonic DMR-XS350 to
the TV as it records in HD to the hard disc. I use HDMI with no problems
at all.

--
Adrian

I had my Panasonic TV connected to my Panasonic DVD recorder and could
nopt work out why, everytime I switched the TV off to stanby with it's
remote, it switched the DVD Recorder off permanently.

Visited the shop where I got both items from and the salesman was
mystified. They sent the TV installer to see if he could work out what I
was meaning. He was baffled also when he tried it.

When I told him that the only thing I had done was put the HDMI cable on
he said that was the problem. Removed it and all is well again now.

Jim

Yep, funny things do seem to occur with the HDMI connector (up-market,
gold-plated version!), more options - Viera? link. Now getting DVB as
default when turning it all on - default was Freesat from the dish, so have
to select HDMI input from menu. Probably an option somewhere (TV and/or DVD
remote?) to default to Freesat input. Cabling DVD/TV done as per manual(s).
But I now get HD reception, noticeably sharper/clearer, so I'll need to be
bored before experimenting further.
Analogue/antenna reception here is poor, and digital (Freeview) non-existent
(so DVB tuning reporting "No stations" was expected).

Keith