Astratec stb problem
 

Everything seemed fine after the digital retune with our TVs and STBs but
I've just realised that our Astratec box can't display STVSCO. (We live in
Ayr, SW Scotland).

It appears in the program list (correctly as channel 3), the program guide
works but when I switch to channel 3, all I get is a black screen.

I've reset the box and rescanned several times (both to add new channels and
also to replace all channels) but it steadfastly refused to display channel
3. I can view channel 3 on all our other STBs & TVs. There are no software
updates available for this STB.

Any suggestions?

Astratec stb problem
 

Tim Downie wrote:
Everything seemed fine after the digital retune with our TVs and STBs
but I've just realised that our Astratec box can't display STVSCO. (We
live in Ayr, SW Scotland).

It appears in the program list (correctly as channel 3), the program
guide works but when I switch to channel 3, all I get is a black screen.

I've reset the box and rescanned several times (both to add new channels
and also to replace all channels) but it steadfastly refused to display
channel 3. I can view channel 3 on all our other STBs & TVs. There are
no software updates available for this STB.

Any suggestions?

Which model is it? Have you tried a full reset then power cycle and
then retune?

There are software updates to these AFAIK , if you do the 'check for
updates' is just checks if one is being broadcast at the moment, and
they only last a few days normally. They are often rebroadcast, is
there a chance you might have missed it, you have to accept it at the
time, otherwise it won't update.

What is you current software (the long number at the bottom of the
screen starting with TUTV probably).

--
Tony

Astratec stb problem
 

Have you tried contacting Humax? There is evidence on the web that this box
and the Humax MG-TU1 may be the same.

Paul DS

"Tim Downie" wrote in message
...
Everything seemed fine after the digital retune with our TVs and STBs but
I've just realised that our Astratec box can't display STVSCO. (We live
in Ayr, SW Scotland).

It appears in the program list (correctly as channel 3), the program guide
works but when I switch to channel 3, all I get is a black screen.

I've reset the box and rescanned several times (both to add new channels
and also to replace all channels) but it steadfastly refused to display
channel 3. I can view channel 3 on all our other STBs & TVs. There are
no software updates available for this STB.

Any suggestions?

Astratec stb problem
 

"Tony" wrote in message
. ..
Tim Downie wrote:
Everything seemed fine after the digital retune with our TVs and STBs but
I've just realised that our Astratec box can't display STVSCO. (We live
in Ayr, SW Scotland).

It appears in the program list (correctly as channel 3), the program
guide works but when I switch to channel 3, all I get is a black screen.

I've reset the box and rescanned several times (both to add new channels
and also to replace all channels) but it steadfastly refused to display
channel 3. I can view channel 3 on all our other STBs & TVs. There are
no software updates available for this STB.

Any suggestions?

Which model is it? Have you tried a full reset then power cycle and then
retune?

Yup.

There are software updates to these AFAIK , if you do the 'check for
updates' is just checks if one is being broadcast at the moment, and they
only last a few days normally. They are often rebroadcast, is there a
chance you might have missed it, you have to accept it at the time,
otherwise it won't update.

What is you current software (the long number at the bottom of the screen
starting with TUTV probably).

TUTV-1-8301-0300d-32-0438

Tim

Astratec stb problem
 

Tim Downie wrote:

"Tony" wrote in message
. ..
Tim Downie wrote:
Everything seemed fine after the digital retune with our TVs and STBs
but I've just realised that our Astratec box can't display STVSCO.
(We live in Ayr, SW Scotland).

It appears in the program list (correctly as channel 3), the program
guide works but when I switch to channel 3, all I get is a black screen.

I've reset the box and rescanned several times (both to add new
channels and also to replace all channels) but it steadfastly refused
to display channel 3. I can view channel 3 on all our other STBs &
TVs. There are no software updates available for this STB.

Any suggestions?

Which model is it? Have you tried a full reset then power cycle and
then retune?

Yup.

There are software updates to these AFAIK , if you do the 'check for
updates' is just checks if one is being broadcast at the moment, and
they only last a few days normally. They are often rebroadcast, is
there a chance you might have missed it, you have to accept it at the
time, otherwise it won't update.

What is you current software (the long number at the bottom of the
screen starting with TUTV probably).

TUTV-1-8301-0300d-32-0438

Tim


You didn't say what the model was, but I do see some references to 0453
on Digitalspy, so it maybe that that might work better, but its hard to
be sure that it is applicable to your model exactly, or that it isn't a
new bug.

Its unusual to get the channel id and no picture atall, I presume you
are getting Ch4 and Ch5 ok?

--
Tony

Astratec stb problem
 

Its unusual to get the channel id and no picture atall, I presume you are
getting Ch4 and Ch5 ok?

My neighbours Sagem IDT 62 with very old firmware gives a badly mangled
picture and no sound. Apparently with newer firmware it would have worked
fine.

Paul DS.

Astratec stb problem
 

Tony wrote:
Tim Downie wrote:
TUTV-1-8301-0300d-32-0438

Tim


You didn't say what the model was, but I do see some references to
0453 on Digitalspy, so it maybe that that might work better, but its
hard to be sure that it is applicable to your model exactly, or that
it isn't a new bug.

Its unusual to get the channel id and no picture atall, I presume you
are getting Ch4 and Ch5 ok?

Doh! I had done a full reset, turned it on and off with the remote but had
forgotten that that's not the same as fully powering down.

A quick unplug from the wall and re-plug has it all sorted. Sorry for
wasting everyone's time!

Tim

Astratec stb problem
 

"Paul D.Smith" wrote in message
...
Have you tried contacting Humax? There is evidence on the web
that this box and the Humax MG-TU1 may be the same.

Paul DS


Yes and no Paul. The on-screen display is very similar, but the
machine is not.

Specifically following Sept 30th the MG-TU1 will no longer work
(or at least ours won't) but both of our Astratecs (3D) work
perfectly.



--
Woody

harrogate three at ntlworld dot com

Astratec stb problem
 

Woody wrote:
"Paul D.Smith" wrote in message
...
Have you tried contacting Humax? There is evidence on the web
that this box and the Humax MG-TU1 may be the same.

Paul DS


Yes and no Paul. The on-screen display is very similar, but the
machine is not.


Actually I would say the opposite is true, the GUI is different but the
hardware is the same (except maybe modulator).

Specifically following Sept 30th the MG-TU1 will no longer work
(or at least ours won't) but both of our Astratecs (3D) work
perfectly.


Not atall, or just messed up a bit?

--
Tony

Astratec stb problem
 

"Tony" wrote in message
. ..
Woody wrote:
"Paul D.Smith" wrote in message
...
Have you tried contacting Humax? There is evidence on the
web that this box and the Humax MG-TU1 may be the same.

Paul DS


Yes and no Paul. The on-screen display is very similar, but
the machine is not.


Actually I would say the opposite is true, the GUI is different
but the hardware is the same (except maybe modulator).

Specifically following Sept 30th the MG-TU1 will no longer
work (or at least ours won't) but both of our Astratecs (3D)
work perfectly.


Not atall, or just messed up a bit?

--
Tony



Got well messed up - some 800's. But the main problem was that it
got 'stuck' in scanning - admittedly never having been fast, but
this time it was taking the better part of an hour to scan, and
we only have Emley signle site. (And yes, I did try attenuation,
cable out, etc, but it made no difference.)


--
Woody

harrogate three at ntlworld dot com

Astratec stb problem
 

Got well messed up - some 800's. But the main problem was that it got
'stuck' in scanning - admittedly never having been fast, but this time it
was taking the better part of an hour to scan, and we only have Emley
signle site. (And yes, I did try attenuation, cable out, etc, but it made
no difference.)

Sounds like my neighbours Sagem with old firmware. Found about 10 out of
100 TV & Radio channels and even the ones it found would not work. TV gave
pictures which partly appeared (strips not pixellation!) and radio sounded
like there was a cat being strangled somewhere nearby.

Paul DS.

Astratec stb problem
 

Woody wrote:
"Tony" wrote in message
. ..
Woody wrote:
"Paul D.Smith" wrote in message
...
Have you tried contacting Humax? There is evidence on the
web that this box and the Humax MG-TU1 may be the same.

Paul DS

Yes and no Paul. The on-screen display is very similar, but
the machine is not.

Actually I would say the opposite is true, the GUI is different
but the hardware is the same (except maybe modulator).

Specifically following Sept 30th the MG-TU1 will no longer
work (or at least ours won't) but both of our Astratecs (3D)
work perfectly.

Not atall, or just messed up a bit?

--
Tony



Got well messed up - some 800's. But the main problem was that it
got 'stuck' in scanning - admittedly never having been fast, but
this time it was taking the better part of an hour to scan, and
we only have Emley signle site. (And yes, I did try attenuation,
cable out, etc, but it made no difference.)



Yes they do seem to get stuck on scan sometimes (before the big change),
a full reset usually sorts it out. Or maybe the new broadcasts are
confusing it, but I can't imagine it would wait for 1hr then give up on
something, so an intermittent bug IMO.

--
Tony

Astratec stb problem [update]
 

Tim wrote:


Doh! I had done a full reset, turned it on and off with the remote
but had forgotten that that's not the same as fully powering down.

A quick unplug from the wall and re-plug has it all sorted. Sorry for
wasting everyone's time!

Turns out the box *is* playing up. I've had to power it down & up 4 times
now due to loss of picture.

CPC who I ordered it from couldn't have been more helpful when I phoned them
and it's getting collected tomorrow.

Tim